How To Close A Polaroid Land Camera

Introduction

This guide shows you how to completely disassemble your camera.

This teardown is non a repair guide. To repair your Polaroid I-Stride 600, use our service manual.

• Open the flash/lens compartment of the Polaroid camera to a thirty degree angle with the horizontal.



• Separate the flash department of the camera from the main body by unhooking the sides.

• Exist CAREFUL NOT TO YANK THE 2 SECTIONS APART BECAUSE THE Band WIRE Nonetheless ATTACHES THEM!

• Open the battery/ cartridge compartment fully.

• Insert spudger in betwixt face of camera and sides where the iv tabs are located.

• In one case tabs are released, pull confront of photographic camera straight out.

• Remove the capture button if it did not pop out when you removed the face.

• There are two pieces to the capture button and both should be removed.

• To remove the back of the camera, you lot have to discover the tabs located almost the hinges of the battery and film compartment.

• Using a spiral driver, pry the tabs of the outer case away from the metal frame.

• Once the tabs are removed slide the metal frame forrad.

• Remove the battery and film compartment latch

• Pull the metallic frame away from the case.

• The entire instance will come off but the flash compartment will come with the insides of the camera.

• Using a spudger, pop the battery and film cartridge hatch from its hinges.

• The tabs are located at the bottom of the metal frame.

• Remove the sight past lifting it direct up.

• Follow the scarlet wire from the wink compartment

• Have the red wire off of the 2 hooks

• Slide the uncovered wire cease out of the small brass clip. Move wire away from photographic camera.

• Follow the black wire from flash bulb to the back of the example.

• When you find the brass tab, pull it upward. When the tab is free, remove the tab from the blackness wire.

• Follow the metallic ring from the flash compartment to the brass tab.

• Unhook the wire on the left of the contumely tab.

• Remove the metal band from behind the brass clip.

• Set the at present detached flash compartment to the side.

• Pull the brass tab up and out like the offset 1 and remove the uncovered wire.

• Slide the brightness adjuster to correct and off the camera.

• Use the pointed end of the spudger to lift a small latch located next to the bottom of lenz plate

• Then find the small latch located beneath the plastic bridge that is over the shutter machinery

• This latch is small and is difficult to run across but you merely have to push it with the pointed end of the spudger to unlatch it.

• Using the pointed end of the spudger, pull the ring wire out of the electric motor.

• In the same manner as above, remove the ring wire from the plastic extension.

• Rotate the lens plate up to unhook the plat from two tabs located at the top of the plate.

• Remove the lens plate, flash compartment and wires from the photographic camera.

• Follow the uncovered wire effectually the side of the camera

• Remove the metallic spring tab next to the counter

• Remove the brass tab by lifting the height piece over the notch and sliding back.

• Locate the small brass tab with the uncovered wire running through information technology.

• Remove the wire by sliding under the hooks.

• so unhook the uncovered wire from the the concluding latch located on the tiptop of the plastic extension.

• The cameras insides could now be in 2 major pieces.

• The Pyramid and the lens plate

• The top of the pyramid has cover that can be lifted off

• Below is the mirror which is held in by a tab.

• Elevator the tab with the spudger and popular out the mirror.

• If y'all intend to reassemble the camera brand sure the mirror is completely make clean without any spots or fingerprints because they will touch on the quality of your pictures.

• In that location are 4 tabs total that must be removed for the adjacent step

• The first is directly nether the leap mounted at the back left of the camera

• The next is located on the front of the plastic extension

• The third tab is used to connect the metal frame to the outer plastic

• The final tab holds several spring loaded pieces together, these may pop out the moment the tab is released.

• The final tab is located below the backside of the photograph-counter dial.

• The numbers will be right side upward if y'all are looking in the right management.

• Once all four tabs are removed the plate pulls out from the slot in the rear.

• Lift the large gear abroad from its pin

• The next slice is loaded with a small spring.

• Carefully lift the "Y" shaped plastic piece from its pin and pull the jump from the pin as information technology is removed.

• Remove the Bound attached to the photo-counter punch.

• Elevator the photo-counter Punch off of its pin.

• Remove the bound attached to the film eject metal slide.

• Remove the film eject metal slide

• Remove the plastic extension past pulling it from the slot in the rear of the camera.

• Remove the metal gear from the gear set.

• Pull the "Fifty" shaped black plastic piece off of its pivot.

• In that location are four gears to remove.

• The gear on the left goes start, followed by the the right.

• The right gear has a small leaf spring betwixt information technology and the gear below it.

• So remove the black gear and then the last white gear.

• Using the pointed end of the spudger, press the clip that is beneath all the gears next to the electric motor gear.

• Lift the plastic box containing several long metallic tabs

• Then slide the box out.

• Pull the electric motor direct out of the plastic piece.

• Remove the jump located in the middle of the plastic mechanism.

• Remove the two loose plastic pieces.

• To remove the metal frame, printing the two tabs with the spudger and slide it forward.

• With the indicate of the spudger, remove the band wire from the solenoid.

• Remove the pocket-sized LED from its prune, and then lift the flat wire array and the flash compartment away from the dorsum of the lens plate.

• Remove the solenoid from the back of the lens plate by removing the 2 tabs.

• Remove the lens by pressing the tab.

• CAUTION: The lens may popular out when the tab is released.

• Remove the back of the lens plate past unhooking the three clips that concur it together.

• Caution: The Shutter leaves may autumn out during this pace.

• Remove the spring on the plastic span that attaches to the shutter machinery

• Remove the Shutter machinery from the dorsum of the lens plate.

• Remove the Articulate dial by unhooking the tab at the bottom of the dial

• Elevator the light blueish slice out of the mechanism.

• Lift the black piece out of the plastic plate.

• Remove the clear green prism from the plastic plate.

• The disassembled camera.

Squad

Embed this guide

Cull a size and copy the code below to embed this guide as a modest widget on your site / forum.

Preview

Source: https://www.ifixit.com/Teardown/Polaroid+One-Step+600+Teardown/2151

Posted by: guffeysche1949.blogspot.com

Share this post